nedoPC.org

PCE Firmware Version 1.01.00:
Copyright 1987 NORMEREL Systemes .
Illegal NMI Trap!!
Wild Hardware Interrupt No:
UnLocatable Parity Error!
Parity Error
(c) Copyright 1987
NORMEREL Systemes
...Can't load - [ENTER] to retry:
ROMBIOS  Ver:1.08
Equipment:
System Devices ok
Video Cards
CMOS RTC/RAM
RAM Memory Kb
Serial Ports
Printer Ports
Diskette Adaptor
Diskette Drives
Hard Drives
Numeric Processor
Option ROMS

Press "y" to begin formatting drive $
IDE Superbios Rev. 1.0 (C) Copyright Western Digital Corp.

Current Drive is $:, Select new Drive or RETURN for curre
$
Current Interleave is $, Select new Interleave or RETURN f
$
Are you dynamically configuring the drive - answer Y/N $
Key in disk characteristics as follows:ccc h rrr ppp ee o
where
ccc = total number of cylinders (1-4 digits)
h = number of heads (1-2 digits)
rrr = starting reduced write cylinder (1-4 digits)
ppp = write precomp cylinder (1-4 digits)
ee = max correctable error burst length (1-2 digits)
     range = 5 to 11 bits, default = 11 bits
 o = CCB option byte, step rate select (1 hex digit)
     range = 0 to 7, default = 5
     refer to controller and drive specification for step
$
Are you virtually configuring the drive - answer Y/N $
Key in cylinder number for virtual drive split as vvvv ...
where vvvv = number of cylinders for drive C: (1-4 digits)
$
Formatting . . .
$+¦Х¦p¦4¦_¦н¦J¦З¦¦J¦
§CORRECTABLE ECC ERROR
§FLAGGED AS BAD SECTOR
¶FLAGGED AS BAD TRACK
MISSING ID FIELD
MISSING DATA ADDR MARK
PROGRAM ERROR
UNCORRECTABLE ECC ERROR
UNREADABLE TRACK
USER-SUPPLIED
$: Aggregate virtual size exceeds disk cylinder size
$: Invalid drive
$: Too many virtual drives
$: Interleave factor must be 1 - 16
$: Interleave factor must be 1 - 25
$: Invalid CCB option value
$: Illegal character
$: Error burst length must be 5 or 11
$: Sector number must be 1-17
$: Cylinder size exceeds maximum
$: Number of heads exceeds maximum
$ : pool size exceeds maximum
$
Do you want to format bad tracks - answer Y/N $
Key in bad track list as follows: ccc h ...
where
ccc = bad track cylinder no (1-4 digits)
h = bad track head number (1-2 digits)
$
                               BAD TRACK MAP
TRACK ADDR          PROBLEM          TRACK ADDR          PROBLEM
$
The surface analysis processor detected no disk errors
$
Dynamic memory space exhausted - cannot complete surface analysis
$
Too many disk errors - cannot complete alt track/sector assignments
$
 Screen full - hit any key to continue
$
More ? Y/N $ with interleave $
Format Successful$

System will now restart

Insert DOS diskette in drive A:
Press any key when ready.  $
Error---completion code $
Nothing Done Exit$

0000FFF0: EA5BE000F0                   jmp       0F000:0E05B
...
0000E05B: FA                           cli
0000E05C: EA0C8000F0                   jmp       0F000:0800C
...
0000800C: FA                           cli
0000800D: EB4D                         jmps      00000805C
...
0000805C: 2AC0                         sub       al,al; = 0
0000805E: E6A0                         out       0A0,al

8350  .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1C
8360  FF 86 FF 55 55 05 FF F0-40 20 10 00 0F 03 .. ..

;----------------- Peripheral settings in System I/O Area FFF0H to FFFFH
0000806B: FC                           cld
0000806C: BE5F83                       mov       si,0835F; offset code
0000806F: BAF0FF                       mov       dx,0FFF0; begin of system area
00008072: B90F00                       mov       cx,0000F; counter of bytes

00008075: AC                           lodsb
00008076: 3CFF                         cmp       al,0FF ;
00008078: 7403                         je        00000807D   -------- (1)
0000807A: EE                           out       dx,al

0000807B: EB00                         jmps      00000807D   -------- (2)

0000807D: 42                           inc       dx; next port of system area
0000807E: E2F5                         loop      000008075   -------- (3)
00008080: E9F804                       jmp       00000857B   -------- (4)

0FFFDH OPCN   03h; xxxx0011b
                         11 DMARQ3/RxD = RxD; DMAAK3/TxD = TxD; INTAK/SRDY/TOUT1 = SRDY
                       00 INT1 = INTP1 Pin; INT2 = INTP2 Pin
0FFFDH OPSEL  0Fh; xxxx1111b - all peripherals Enabled
0FFFCH OPHA = 00h; Ports at zero seg.area 00xxh
0FFFBH DULA = 10h; DMA control unit       0010h
0FFFAH IULA = 20h; Interrupt control unit 0020h
0FFF9H TULA = 40h; Timer/counter unit     0040h
0FFF8H SULA =0F0h; Serial control unit    00F0h non standart (Math Coprocessor)
0FFF7H reserve FF
0FFF6H WCY2 = 05h;
0FFF5H WCY1 = 55h;
0FFF4H WMB  = 55h;
0FFF3H reserve FF
0FFF2H RFC  = 86h;
0FFF1H reserve FF
0FFF0H TCKS = 1Ch;